Skip to main content
CalcSummitCalcSummit
Area Calculator · Interior · Roll Strips · Pad

Carpet Calculator

To find how much carpet you need, plan strips from the roll width, not only floor area. Floor area divided by 9 gives square yards. A 12 by 12 foot room on a 12 foot roll needs two strips once you allow 3 inches of trim on each wall. Enter your rooms and roll width below.

This tool is part of our area calculators. Use it for one room or up to ten.

  • Updated November 2026
  • Sources Cited
  • No Login Required
  • Free to Use
Live Calculator · Strips · Seams · Square Yards

Carpet Roll Planner

Rooms (wall to wall)

Room 1

Roll width
Layout options

CRI 105 asks for at least 3 in of carpet along each wall for trimming. Enter 0 to see the layout minimum.

Leave the pattern repeat at 0 for plain carpet. For a patterned carpet, enter the repeat length from the sample.

Prices (optional)

Order this much carpet

25.83 sq yd

232.5 sq ft | 25.83 sq yd | 21.6 sq m

Roll length
15.5 ft
Seams
0
Floor area
180 sq ft
Waste over floor
29.2%

1 strip, no seam, 15.5 linear feet of 15 ft roll, 25.83 sq yd to order, 29.2% over floor area. A 13 ft 6 in roll needs the least carpet for these rooms. See the table below.

Pad: 20 sq yd (180 sq ft) including a 0% allowance.

Strip plan by room for the selected roll width
RoomSize (ft)StripsStrip length (ft)SeamsOrdered (sq ft)
115 x 121 running along the 15 ft side15.50232.5
The same rooms planned on each roll width
Roll widthOrdered (sq ft)Ordered (sq yd)SeamsWaste over floor
12 ft30033.33166.7%
13 ft 6 in(least carpet)209.2523.25016.3%
15 ft232.525.83029.2%

Every strip is a full roll width and runs the same way, as CRI 105 section 5.2 requires. Roll widths vary by carpet line, so confirm the width and any partial-roll policy with your supplier. Remnants are not reused in this plan.

Strip plan per room

Each room is cut along its length or width, whichever uses less carpet.

Seams counted

See where a room needs a seam and how a wider roll removes it.

Roll widths compared

The same rooms on 12 ft, 13 ft 6 in and 15 ft rolls, side by side.

Estimates are for material planning. Roll widths vary by carpet line, so confirm the width with your supplier. Your installer makes the final cut plan.

Advertisement

How to work out how much carpet you need

Carpet comes off a roll in full-width strips. Measure each room, choose a roll width, add 3 inches of trim to each wall, and count the strips. Multiply the strip length by the strips and by the roll width to get the square feet to order. Divide by 9 for square yards.

  1. Measure each room in feet and inches, wall to wall.
  2. Pick the roll width. The calculator tries strips along the length and along the width.
  3. Strips = (width across the strips + trim on both walls) divided by the roll width, rounded up.
  4. Strip length = the room length along the strips plus trim on both ends.
  5. Ordered area = strips x strip length x roll width. Seams = strips minus 1.

If you only have floor measurements, start from our square footage calculator to check the floor area. The strip plan still needs each room's length and width.

Worked examples: 12 by 12, 12 by 15 and 14 by 14 foot rooms

A 12 by 12 foot room has 144 sq ft of floor, or 16 sq yd. Add 3 inches of trim on each wall and the room is 12.5 feet across, which is wider than a 12 foot roll. The plan needs two strips and 33.33 sq yd. On a 15 foot roll the room needs one strip and 20.83 sq yd.

Strips, seams, strip length, square yards to order and waste for common rooms and roll widths.
RoomFloor (sq ft)RollStripsSeamsStrip (ft)Order (sq yd)Over floorArea + 10% (sq yd)
12 x 12 ft14412 ft2112.533.33108.3%17.6
12 x 12 ft14415 ft1012.520.8330.2%17.6
15 x 12 ft18012 ft2112.533.3366.7%22
15 x 12 ft18013 ft 6 in1015.523.2516.3%22
15 x 12 ft18015 ft1015.525.8329.2%22
14 x 14 ft19612 ft2114.538.6777.6%23.96
14 x 14 ft19615 ft1014.524.1711%23.96

Trim is 3 inches on each wall, with no pattern repeat. Each row uses the strip direction that needs the least carpet. Figures come from this calculator's strip model, not a supplier quote.

A 12 by 15 foot room on a 12 foot roll: strip 1 covers 12 feet of the width, and strip 2 covers the last 3 feet with the rest of the strip left as offcut.
Figure B. Two 12 foot wide strips cover a room 15 feet wide. The second strip is mostly offcut. Source: this calculator.

Why roll width changes how much carpet you order

Roll width sets how many strips a room needs, and each extra strip adds a seam and an offcut. For a 12 by 15 foot room the plan needs 33.33 sq yd on a 12 foot roll, 23.25 sq yd on a 13 foot 6 inch roll and 25.83 sq yd on a 15 foot roll. Floor area plus 10 percent gives 22 sq yd.

The widest roll is not always the cheapest order. Here the 13 foot 6 inch roll needs less carpet than the 15 foot roll, because both cover the 12.5 foot width in one strip. The calculator compares every roll width for your rooms. The 12 ft, 13 ft 6 in and 15 ft widths come from a competitor calculator page, not a standard, so confirm the width with your supplier.

Bar chart for a 12 by 15 foot room: 22.00 sq yd by area formula, 33.33 on a 12 foot roll, 23.25 on a 13 foot 6 inch roll, 25.83 on a 15 foot roll.
Figure C. Square yards to order for a 12 by 15 foot room by roll width. Trim is 3 inches on each wall. Source: this calculator.

Seams, trim and pile direction

The CRI 105 residential installation standard asks for at least 3 inches of carpet along each wall for trimming (Section 5.3). It requires the same pile direction on adjacent pieces of the same carpet unless the specification says otherwise (Section 5.2). So offcuts are not turned, and every strip in the plan is a full roll width.

Section 5.1 says to keep seams to a minimum and lists how to place the ones you need:

  • Keep seams away from areas with pivoting traffic.
  • Do not run a seam perpendicular to a doorway opening.
  • Run main traffic parallel to a seam, not across it.
  • Keep natural light from striking across the seam.
Note
The calculator counts seams. It does not choose their position. Your installer marks the seams on the room diagram. Ask where each one will fall before you order.

How to measure a room for carpet

Measure the longest length and the widest width, wall to wall, in feet and inches. Include closets and doorway thresholds that get carpet. Split an L-shaped room into rectangles and enter each as its own room. Write down the sizes before you shop.

Our feet and inches calculator adds measurements that mix feet and inches. The planner takes up to 10 rooms.

Carpet pad

The calculator estimates pad from floor area plus the allowance you enter, which is 0 percent by default. Pad is laid under the carpet across the floor, so it does not follow the roll plan. Confirm the pad quantity with your installer, because pad is sold in its own rolls.

This page makes no claim about pad thickness or density. Follow the carpet maker's pad requirement for your product.

Square feet, square yards and square meters

Carpet is often priced per square yard. One square yard is 9 square feet, because it is 3 feet by 3 feet. One square foot is exactly 0.09290304 square meters. The result card shows the order in all three units, and the toggle sets the large figure.

A 12 by 15 foot room is 180 sq ft, 20 sq yd or about 16.72 sq m of floor. The order is larger than the floor because of trim and strip width.

What this calculator does not cover

  • Stairs. For stair geometry, use our stair calculator. Stair carpet is not sized here.
  • Reuse of offcuts. Every strip is a full roll width and remnants are not reused.
  • Seam positions, which your installer decides.
  • Installed prices. Enter your own carpet and pad prices for a material figure. For installed ranges, use the flooring cost calculator.
  • Metric room input. Results can be shown in square meters.

For other floor types, see the flooring calculator.

Methodology and sources

Published November 2026. Last updated November 2026. Next review February 2027.

Sarah Kim, CPE, CPE — CalcSummit expert reviewer

Reviews: cost calculators · 24 calculators reviewed

Sarah Kim is a Certified Professional Estimator (CPE) with 15 years of construction cost estimation experience. She holds CPE certification from ASPE (member #20-4891). At Turner Construction, she managed material cost analysis on commercial projects ranging from $2M to $45M. At CalcSummit, she writes and verifies all cost estimation and interior finish calculators, updating regional cost benchmarks quarterly using RS Means-informed data.

Full profile →

Frequently asked questions

Advertisement

Advertisement