Skip to main content
CalcSummitCalcSummit
Guide · Conversion · Feet on a Tape

How to Measure a Foot on a Tape Measure

A foot is 12 inches. To measure a foot, hook the tip on the start point, pull the tape straight, and read to the 12 inch mark. Many tapes print a foot number there. Read the inches and fractions past that mark, then write feet first.

Need to add or convert a reading? Use the feet and inches calculator.

  • Updated November 2026
  • Sources Cited
  • No Login Required
  • Free to Use

What Is a Foot on a Tape Measure?

A foot is a unit of length equal to exactly 12 inches. On a tape measure, the 12 inch mark is the first foot. The 24 inch mark is the second foot, and the 36 inch mark is the third. Some tapes print a black foot number above the 12 inch mark and use red numbers for the inches that follow. A 12 ft tape reads out to 144 in. In metric, 1 ft equals exactly 0.3048 m.

  • First foot: the 12 inch mark.
  • Second foot: the 24 inch mark.
  • Third foot: the 36 inch mark.

For other unit jobs, browse the conversion calculators hub.

How to Measure a Foot, Step by Step

Follow these six steps for any length, from one foot to a full 12 ft tape.

  1. Hook the tip on the start edge. Set the metal tip on the edge where the length starts. The tip slides slightly, so it stays accurate when you hook it over an edge.
  2. Pull the tape straight and lock it. Keep the tape flat and tight along the line you are measuring. Lock the blade so the reading does not move.
  3. Find the last foot mark you passed. Look back along the tape for the last 12, 24, 36 or 48 inch mark before your end point. That count is your feet.
  4. Read the whole inches past that mark. Count the numbered inches from the foot mark to your end point. Add them to the feet.
  5. Read the fraction from the hash marks. Find the nearest hash mark. The longest is 1/2 in, then 1/4 in, 1/8 in and 1/16 in. Count marks in sixteenths if the mark is small.
  6. Write feet first, then inches. Write the reading as feet, then inches, then the fraction. Example: 3 ft 7 1/2 in.

How to Read Inches and Fractions Past the Foot Mark

Between two inch numbers the tape prints hash marks. The longest mark sits halfway and means 1/2 in. A slightly shorter mark means 1/4 in or 3/4 in. Shorter marks mean 1/8 in and 1/16 in. Many tapes stop at 1/16 in. To read a small mark, count it in sixteenths of an inch. A mark 9 steps past the inch number reads 9/16 in.

Hash mark, sixteenths of an inch and decimal inches for the four common marks.
Hash markSixteenthsDecimal inches
1/2 in8/160.5
1/4 in4/160.25
1/8 in2/160.125
1/16 in1/160.0625
Hash marks on one inch of tape: 1/2 inch is the longest, then 1/4, 1/8 and 1/16 inch. One inch holds 16 sixteenths.
Figure B. One inch of tape. The 1/2 in mark is longest, and each shorter mark halves the step down to 1/16 in.

Tape Readings in Feet and Inches

Use this table to turn a total reading in inches into feet and inches. Divide by 12 for the feet. The remainder is the inches. The decimal column is the same length as one number, which you need before you multiply lengths.

Nine tape readings in inches with the matching feet and inches and decimal feet.
Tape readingFeet and inchesDecimal feet
12 in1 ft 0 in1 ft
24 in2 ft 0 in2 ft
36 in3 ft 0 in3 ft
48 in4 ft 0 in4 ft
60 in5 ft 0 in5 ft
72 in6 ft 0 in6 ft
87 in7 ft 3 in7.25 ft
96 in8 ft 0 in8 ft
144 in12 ft 0 in12 ft

Worked Example: Reading a Wall

Tip
Worked example. A wall reads 3 ft 7 1/2 in. Total inches are 3 x 12 + 7.5 = 43.5 in. Decimal feet are 43.5 / 12 = 3.625 ft. Use 3.625 ft when you multiply this wall by another length. Use 3 ft 7 1/2 in when you mark the cut.

To add or subtract readings like this one, use the feet and inches calculator. To turn a length into area, see the square footage calculator.

Common Mistakes When Reading Feet

  • Reading a decimal foot as inches. 5.5 ft is 5 ft 6 in, not 5 ft 5 in. Multiply the decimal part by 12.
  • Skipping a foot mark on a long run. Count the foot numbers as you pull the tape.
  • Dropping the fraction. Eight cuts that are each 1/16 in short add up to 0.5 in.
  • Writing feet and inches as one decimal. Write 3 ft 7 1/2 in, not 3.7 ft.

Measuring Your Own Foot for Shoes?

This guide covers the foot as a unit of length on a tape measure. Shoe sizing is a different task. Shoe makers publish their own size guides, so use the guide from the brand you are buying.

Frequently Asked Questions

Advertisement

Sources and Review

Note
How the numbers were checked. Every figure on this page was recomputed by code from 1 ft = 12 in. The tape table, the hash mark table and the worked example come from the same functions.

Sources

Published November 2026. Last updated November 2026. Next review May 2027. Technical review is pending. This page explains how to read a tape. It is not a design or a bid. For structural, code or permit work, confirm dimensions with the licensed professional on the project.

Rachel Torres, M.Ed., M.Ed. — CalcSummit expert reviewer

Reviews: conversion calculators · 22 calculators reviewed

Full profile →