Skip to main content
CalcSummitCalcSummit
Guide · Conversion · Linear Feet

How to Figure Linear Feet

A linear foot is 12 inches of length, measured along one line. To figure linear feet, measure each run in feet, add the runs, and divide any inches by 12. Width and thickness do not count. A 96 inch board is 8 linear feet, and a 12 ft by 12 ft room has a 48 linear foot perimeter.

Need to convert inches to feet first? Use the feet and inches calculator.

  • Updated November 2026
  • Sources Cited
  • No Login Required
  • Free to Use

What Is a Linear Foot?

A linear foot is 12 inches of length along a straight line. It is the same length as a regular foot. Linear feet is also written linear ft or LF. The word linear tells you that only length counts. A board that is 2 in wide and a board that is 12 in wide are both 8 linear feet when each is 8 ft long. Trim, fence, gutter and railing are sold and priced by the linear foot. Floor and wall coverings are sold by the square foot.

  • 1 linear foot = 12 inches of length.
  • Width and thickness never count.
  • 10 linear feet is the same length as 10 ft.

For other unit jobs, browse the conversion calculators hub.

How to Figure Linear Feet, Step by Step

Follow these six steps for trim, fence, gutters, decking or any other material sold by length.

  1. Measure each straight run. Use a tape measure end to end on each wall, board or fence side. Measure runs that turn a corner as separate runs.
  2. Write every run in feet. Divide any inches by 12. For example, 8 ft 6 in is 8.5 ft.
  3. Add the runs together. The total of all runs is the linear feet. Keep the sum in feet, not in feet and inches.
  4. Subtract openings the material skips. Take off door openings for baseboard and gate openings for fence. Leave openings in for crown molding, which runs over them.
  5. Add waste for cuts. Multiply by 1 plus the waste percent. A 10 percent allowance turns 422 linear feet into 465.
  6. Divide by the stock length. Divide the total by the length of one stick or panel, then round up to a whole piece.

Linear Feet Formulas

Three formulas cover almost every linear feet job. Use the first for a single piece. Use the second for a room or yard. Use the third when a floor or deck is measured in square feet and the boards are bought by the foot.

Formula and worked example for a single piece, a rectangle perimeter and boards that cover an area.
UseFormulaExample
Single piecelinear feet = inches / 1296 / 12 = 8 linear feet
Rectangle perimeterlinear feet = 2 x (length + width)2 x (12 + 12) = 48 linear feet
Boards that cover an arealinear feet = square feet x 12 / (face width in + gap in)200 x 12 / (5.5 + 0.1875) = 422 linear feet

Square Feet to Linear Feet Table

Use this table when you know the area and the board width. Use the board's actual face width, not its nominal name. A 1x6 is 5 1/2 in wide, so 100 sq ft takes about 218 linear feet of 1x6, not 200. Values are before waste.

Linear feet of boards for 50, 100, 200 and 300 square feet at four board widths, before waste.
Area3 1/4 in plank flooring5 1/2 in board, butted5 1/2 in deck board, 3/16 in gap7 1/4 in board, butted
50 sq ft185 lf109 lf105 lf83 lf
100 sq ft369 lf218 lf211 lf166 lf
200 sq ft738 lf436 lf422 lf331 lf
300 sq ft1,108 lf655 lf633 lf497 lf

To get the area first, use the square footage calculator.

Worked Examples

One board

Note
Board. A board is 96 in long. Linear feet are 96 / 12 = 8.

A room perimeter

Note
Room. A room is 12 ft by 12 ft. The perimeter is 2 x (12 + 12) = 48 linear feet. Crown molding uses all 48. Baseboard skips one 3 ft door, so it uses 48 - 3 = 45 linear feet.
A 12 ft by 12 ft room has a 48 linear foot perimeter. Crown uses 48 and baseboard with one 3 ft door uses 45.
Figure B. A 12 ft by 12 ft room. Crown molding runs over the doorway, so it uses the full perimeter. Baseboard skips it.

A fence run and a price

Note
Fence. A yard fence has runs of 80 ft, 40 ft, 40 ft. The total is 160 linear feet. At an example price of $3.00 per linear foot, the material is 160 x 3 = $480. The price is an example input, not a quote.

Deck boards from square feet

Note
Deck. A 200 sq ft deck uses 5 1/2 in boards with a 3/16 in gap. Linear feet are 200 x 12 / 5.6875 = 422, which rounds to 422. With 10 percent waste the order is 465 linear feet.

For a full fence estimate, use the fence calculator.

Common Mistakes When Figuring Linear Feet

  • Mixing inches and feet. Write every run in feet first. 8 ft 6 in is 8.5 ft, not 8.6 ft.
  • Using the nominal board width. A 1x6 is 5 1/2 in wide, so the board count comes out higher than the name suggests.
  • Subtracting doors from crown molding. Crown runs over the opening. Baseboard does not.
  • Skipping waste. Cuts, miters and bad boards need an allowance. Pick a percent and show it as a separate line.
  • Treating linear feet as area. A linear foot has no width. Use square feet for coverage and linear feet for length.

Linear Feet, Square Feet and Board Feet

A linear foot is length only. A square foot measures area, such as a floor. A board foot measures the volume of lumber, so it is a different unit from a linear foot. Lumber is often priced by the board foot, and trim and fence by the linear foot. Check which unit a price uses before you compare quotes.

Frequently Asked Questions

Advertisement

Sources and Review

Note
How the numbers were checked. Every figure on this page was recomputed by code from 1 linear foot = 12 in. The formula table, the area table and the worked examples come from the same functions.

Sources

Published November 2026. Last updated November 2026. Next review May 2027. Technical review is pending. This page explains how to figure a length. It is not a design or a bid. For structural, code or permit work, confirm dimensions with the licensed professional on the project.

Rachel Torres, M.Ed., M.Ed. — CalcSummit expert reviewer

Reviews: conversion calculators · 22 calculators reviewed

Full profile →