Skip to main content
CalcSummitCalcSummit
Guide · Project · Stair Stringers

How to Figure Out Stair Stringers

Divide the total rise by about 7 in and round to get the risers. Divide the rise by the risers for the riser height. Treads times tread depth is the run. Stringer length is the square root of rise squared plus run squared. A 50.75 in rise gives 7 risers of 7.25 in and a 78.58 in stringer.

Want the numbers done for you? Use the stair calculator.

  • Updated November 2026
  • Sources Cited
  • No Login Required
  • Free to Use

What a Stair Stringer Needs

A stair stringer is the sloped board that carries the treads. You cut notches in it so each step has the same rise and the same run. You need three numbers before you cut: the total rise, the tread depth and the tread thickness. Total rise is the vertical distance from the lower surface to the top of the upper floor or deck.

  • Total rise: the vertical distance the stair must climb.
  • Tread depth: the horizontal depth of one step. The code minimum is 10 in.
  • Tread thickness: the board you will lay on each notch, such as 1.5 in.

For a whole deck, see the deck building guide. For other jobs, browse the project calculators hub.

How to Figure Out Stair Stringers, Step by Step

Follow these six steps for a straight stair with the top tread level with the upper floor or deck.

  1. Measure the total rise. Measure straight up from the lower surface to the top of the upper floor or deck. Use the finished surfaces. If the lower surface is not built yet, measure to where its top will be.
  2. Count the risers. Divide the total rise by about 7 in and round to a whole number. For 50.75 in, 50.75 / 7 is about 7.25, so use 7 risers.
  3. Find the riser height. Divide the total rise by the number of risers. 50.75 / 7 = 7.25 in. Every riser on the flight uses this height. Check that it is at or under 7.75 in.
  4. Set the tread depth and the total run. Treads on the stringer equal risers minus 1, because the top tread is the upper floor or deck. With 6 treads of 10 in, the total run is 60 in.
  5. Find the stringer length. Use the Pythagorean theorem. The square root of 50.75 squared plus 60 squared is 78.58 in, or 6 ft 6.6 in. Buy a board longer than this, because the ends are cut.
  6. Mark and cut the bottom shorter. Take the tread thickness off the first riser at the bottom. 7.25 - 1.5 = 5.75 in. Then the first step is the same height as the others once its tread is on.

Stair Stringer Formulas

Five formulas cover the layout. Work them in order. The riser count is the only step that needs a judgment call.

Formula and worked example for risers, riser height, total run, stringer length and the bottom cut.
UseFormulaExample
Number of risersrisers = total rise / 7, rounded50.75 / 7 = 7.25, so 7 risers
Riser heightriser = total rise / risers50.75 / 7 = 7.25 in
Total runrun = (risers - 1) x tread depth6 x 10 = 60 in
Stringer lengthlength = sqrt(rise^2 + run^2)sqrt(50.75^2 + 60^2) = 78.58 in
Bottom cutfirst cut = riser - tread thickness7.25 - 1.5 = 5.75 in

Total Rise to Stringer Length Table

Use this table for a quick check before you run your own numbers. Each row uses a 10 in tread and a target riser of about 7 in. Values are exact, with no waste added to the length.

Twelve total rises with the matching number of risers, riser height, total run and stringer length, using a 10 inch tread.
Total riseRisersRiser heightTotal runStringer length
30 in47.5 in30 in42.43 in
36 in57.2 in40 in53.81 in
40 in66.67 in50 in64.03 in
44 in67.33 in50 in66.6 in
48 in76.86 in60 in76.84 in
52 in77.43 in60 in79.4 in
56 in87 in70 in89.64 in
60 in96.67 in80 in100 in
66 in97.33 in80 in103.71 in
72 in107.2 in90 in115.26 in
80 in117.27 in100 in128.06 in
90 in136.92 in120 in150 in

Worked Example

A deck with a 50.75 in rise

Note
Layout. A deck is 50.75 in above the ground. 50.75 / 7 is about 7.25, so use 7 risers of 7.25 in. There are 6 treads of 10 in, so the run is 60 in. The stringer is 78.58 in long, which is 6 ft 6.6 in. The stair angle is about 35.9 degrees.
Side view of a stair with 50.75 inches of rise, 7 risers, 6 treads of 10 inches, a 60 inch run and a 78.58 inch stringer.
Figure A. Total rise, total run and the stringer length as the diagonal.

The bottom cut

Note
Bottom. With 1.5 in thick treads, the first cut at the bottom is 7.25 - 1.5 = 5.75 in. Without this change the first step would be 1.5 in taller than the rest.
A 7.25 inch riser minus a 1.5 inch tread leaves a 5.75 inch first cut at the bottom of the stringer.
Figure B. Cut the first riser shorter by the tread thickness.

To test your own rise and tread, use the stair calculator.

Code Limits to Check

The International Residential Code (IRC R311.7) sets the limits most residential stairs follow. Risers are 7.75 in or less. Treads are 10 in deep or more. The largest and smallest riser in one flight differ by no more than 3/8 in (0.375 in). Local codes can differ, so confirm the code your building department has adopted before you cut.

  • Measure to finished surfaces. Decking, tile or carpet can change the first and last risers.
  • Equal risers meet the 3/8 in spread rule. The bottom cut makes the first riser equal once the tread is on.
  • If the riser comes out over 7 3/4 in, add one riser and divide again.
  • This guide covers the layout math. Handrails, landings and headroom are separate code items. See the stair calculator and your local code.

Common Mistakes When Figuring Stair Stringers

  • Counting the top tread. The upper floor or deck is the top tread, so treads equal risers minus 1.
  • Skipping the bottom cut. The first riser comes out one tread thickness too tall.
  • Using rough measurements. Use finished floor heights, or a riser may change by the thickness of the flooring.
  • Rounding the riser height. Keep the full number when you mark. Round only for the tape reading.
  • Using the run as the stringer length. The stringer is the diagonal, so it is longer than the run.

Frequently Asked Questions

Advertisement

Sources and Review

Note
How the numbers were checked. Every figure on this page was recomputed by code from the formulas in section 03. The formula table, the rise table and the worked example come from the same functions.

Sources

  • Jaspector, IRC 2021 R311.7 Stairways: the 7 3/4 in riser limit, the 10 in tread minimum and the 3/8 in spread rule. Read on November 20, 2026. Code text there is paraphrased from the ICC model code, so check the code your jurisdiction has adopted.

Published November 2026. Last updated November 2026. Next review May 2027. Author and field review sign-off are pending. This page explains the layout math. It is not a stair design, a permit set or a code ruling. For structural, code or permit work, confirm dimensions with the licensed professional on the project and your local building department.

Alex Rivera, PE, PE — CalcSummit expert reviewer

Reviews: volume calculators · 38 calculators reviewed

Full profile →