Skip to main content
CalcSummitCalcSummit
Comparison · Conversion · Feet and Inches

Feet vs Inches: Differences, Symbols and When to Use Each

A foot equals exactly 12 inches, so feet and inches measure the same length at different scales. Feet suit long runs such as walls and rooms. Inches suit short cuts, spacing and thickness. A length of 5 feet 6 inches is 66 inches, or 5.5 feet in decimal form.

Need to add, subtract or convert a measurement? Use the feet and inches calculator.

  • Updated November 2026
  • Sources Cited
  • No Login Required
  • Free to Use

Feet vs Inches at a Glance

A foot is 12 inches. An inch is one twelfth of a foot. Plans mark feet with a single tick and inches with a double tick. Use feet for long runs and inches for short parts. Convert inches to decimal feet before you multiply for area or volume.

Foot and inch compared on symbol, size, metric value, use, tape marking, decimal form and error risk.
AttributeFootInch
Symbol in proseftin
Symbol on plans (tables only)′″
Size12 in1/12 ft
Metric (exact)0.3048 m2.54 cm
Typical useRuns, rooms, lengthsThickness, spacing, short cuts
On a tapeLong marks and feet tagsNumbered marks and fractions
Decimal form1 ft = 1.01 in = 0.0833 ft
Error riskReading 5.5 ft as 5 ft 5 inDropping fractions

What Is a Foot?

A foot is a unit of length equal to 12 inches. Since the 1959 international agreement it equals exactly 0.3048 meter. Builders use feet for room sizes, wall runs and board lengths. On plans the symbol is ft or a single tick, as in 8′. A foot is the larger unit.

  • Size: 12 in, or exactly 0.3048 m.
  • Use: room sizes, wall runs and board lengths.
  • Decimal form: 1 ft is 1.0 ft. Each inch adds 0.0833 ft.

What Is an Inch?

An inch is one twelfth of a foot. It equals exactly 2.54 centimeters. Builders use inches for thickness, spacing and short cuts, such as a 4 in slab or 16 in stud spacing. On plans the symbol is in or a double tick, as in 4″. An inch is the smaller unit.

  • Size: 1/12 ft, or exactly 2.54 cm.
  • Use: thickness, spacing and short cuts.
  • On a tape: numbered marks and fractions of an inch.

Which Symbol Means Feet and Which Means Inches?

The single tick (′) means feet. The double tick (″) means inches. A memory aid: inches has two syllables and takes two ticks, while feet has one syllable and takes one. So 5′ 6″ reads five feet six inches. Many plans write ft and in in words instead of ticks.

How plans write them

A plan may use ticks, the words ft and in, or inches alone. Some plans give an 8 ft wall as 96 in. Read the unit before you read the number.

Plan notation with ticks, how it reads aloud, and the form used in prose on this site.
On a planReads asIn prose
8′eight feet8 ft
4″four inches4 in
5′ 6″five feet six inches5 ft 6 in
8′ 5 5/8″eight feet five and five eighths inches8 ft 5 5/8 in

Feet vs Inches Head to Head

Three jobs decide which unit you reach for. You record a length, you do math with it, and you write it on a plan. Each job has its own best unit.

Record on site

Record a short part in inches. A 4 in slab and 16 in stud spacing stay in inches. Record a run in feet and inches, the way the tape reads. Write the unit with every number so the next reader does not guess.

Do the math

Convert to decimal feet before you multiply. Area and volume formulas need one unit for every length. A 4 in thickness becomes 0.3333 ft. The worked example in section 06 shows the full steps.

Write on a plan

Use ticks, the words ft and in, or inches alone. Pick one style and keep it across the drawing. A reader should never have to convert a number to read it.

How to Convert Between Feet and Inches

Multiply feet by 12 to get inches. Divide inches by 12 to get feet. For 5 ft 6 in, multiply 5 by 12 to get 60, then add 6 to reach 66 in. Divide 66 by 12 to get 5.5 ft. Write the decimal as 5.5 ft, never 5.6 ft.

Feet to inches

Multiply the feet by 12, then add the loose inches. For 5 ft 6 in, that is 5 x 12 + 6 = 66 in. For other measurements, use the feet and inches calculator or browse the conversion calculators.

Inches to feet

Divide the inches by 12. The whole number is the feet. The remainder is the loose inches. For 66 in, 66 / 12 = 5.5 ft, which is 5 ft 6 in.

Eight lengths in plan notation, prose form, total inches and decimal feet.
NotationProseTotal inchesDecimal feet
1′ 0″1 ft 0 in121
2′ 6″2 ft 6 in302.5
3′ 4″3 ft 4 in403.3333
4′ 8″4 ft 8 in564.6667
5′ 6″5 ft 6 in665.5
6′ 0″6 ft 0 in726
8′ 5 5/8″8 ft 5 5/8 in101.6258.4688
10′ 3″10 ft 3 in12310.25
A tape from 0 to 24 inches with foot tags at 12 and 24. A length of 1 ft 6 in is 18 in, or 1.5 ft.
Figure B. A tape marked in inches with foot tags at 12 in and 24 in. 1 ft 6 in is 18 in, or 1.5 ft.

The decimal feet trap

A decimal foot is not feet and inches. The digits after the point are a share of 12 in, not a count of inches. Reading 5 ft 6 in as 5.6 ft adds error to every later number. Use the square footage calculator with decimal feet only after you convert.

Three lengths misread as decimal feet, with the wrong inches, the right inches and the error.
ValueMisread asWrong inchesRight inchesError
5′ 6″5.6 ft67.2 in66 in1.2 in
5′ 3″5.3 ft63.6 in63 in0.6 in
7′ 4″7.4 ft88.8 in88 in0.8 in
Tip
Worked example. A slab is 12 ft by 10 ft by 4 in. Thickness is 4 / 12 = 0.3333 ft. Volume is 12 x 10 x 0.3333 = 40.00 cu ft. Divide by 27 to get 1.48 cu yd. Check it with the cubic feet calculator.

When to Use Feet and When to Use Inches

Use inches for short parts, thickness and tight tolerances. Use feet and inches for room and wall runs read from a tape. Use decimal feet when you multiply lengths for area or volume. The wrong choice causes the most common takeoff error, so convert once and keep that unit all the way through.

Decision matrix: the unit to record, calculate with and write on a plan, by kind of work.
WorkRecordCalculateWrite on a plan
Short parts, thickness, spacingInchesDecimal feet, when you multiplyin
Wall runs, rooms, board lengthsFeet and inchesDecimal feetft and in
Area or volume of a slabFeet for length and width, inches for thicknessDecimal feet for all threeft, with thickness in in

The rule in one line: record short parts in inches, record runs in feet and inches, and convert to decimal feet before you multiply.

Edge Cases

Three cases need care. A fraction such as 5 5/8 in is exact, but decimals are easier in a table. A decimal foot is not feet and inches, so 5.6 ft is 5 ft 7.2 in. Survey work may use the US survey foot, which differs from the international foot by 2 parts per million.

  • Fractions: 8 ft 5 5/8 in is exactly 101.625 in, or 8.4688 ft.
  • Decimal feet: 5.6 ft is 5 ft 7.2 in. 5.5 ft is 5 ft 6 in.
  • Survey foot: 1 international foot is 0.999 998 US survey foot. Use the unit your survey or plan names.

Frequently Asked Questions

Advertisement

Sources and Review

Note
How the numbers were checked. Every figure on this page was recomputed by code from 1 ft = 12 in and 1 ft = 0.3048 m. The conversion table, the error table and the slab example come from the same functions.

Sources

Published November 2026. Last updated November 2026. Next review May 2027. Technical review is pending. This page explains units. It is not a design or a bid. For structural, code or permit work, confirm dimensions with the licensed professional on the project.

Rachel Torres, M.Ed., M.Ed. — CalcSummit expert reviewer

Reviews: conversion calculators · 22 calculators reviewed

Full profile →