Skip to main content
CalcSummitCalcSummit
Conversion Calculators · Comparison

23/32 vs 3/4 Plywood: What the Inch Difference Means

  • Updated November 2026
  • Sources Cited
  • No Login Required
  • Free to Use

23/32 vs 3/4 at a Glance

23/32 inch is 0.71875 inches. 3/4 inch is 0.75 inches. A panel sold as 3/4 inch plywood is usually the 23/32 inch size, so the sheet is 1/32 inch under its name.

That is 0.03125 inches or 0.79 mm, and 4.2% of the nominal thickness. On a single sheet it is small. It adds up in stacks and decides whether a groove cut for a true 3/4 inch panel fits snugly.

Two bars from zero: 23/32 inch is 0.71875 in and 3/4 inch is 0.75 in, a 1/32 inch gap

What Does 23/32 Inch Mean?

23/32 inch means 23 parts of an inch that has been cut into 32 equal parts. Divide 23 by 32 and you get 0.71875 inches. Multiply by 25.4 and you get 18.256 mm.

On a tape, 23/32 sits one mark below 3/4, because 3/4 is 24/32. Most tapes mark 32nds only on the finest ruler line, so people often round 23/32 up to 3/4 by eye. A caliper shows the real value.

What Does 3/4 Inch Mean?

3/4 inch is 0.75 inches, or 19.05 mm. In lumber and panels it is also a trade name. A sheet labeled 3/4 inch is named for the size it was meant to be, not the size it measures.

APA, the engineered wood trade group, says its Performance Category serves as the "nominal panel thickness" in building codes. That is the label, not a measurement. APA's own thickness table was not on the pages read for this article, so the 23/32 figure comes from the retail and guide pages listed in the sources.

23/32 vs 3/4 Head to Head

Side by side, the two sizes differ by one thirty-second of an inch, which is 0.794 mm.

Nominal and actual plywood thickness for 1/4, 1/2, 5/8 and 3/4 inch panels, each actual size 1/32 inch under nominal
Figure A. Nominal and actual thickness for four common panel sizes.
23/32 inch compared with 3/4 inch in fractions, decimals and millimeters
Measure23/32 in3/4 inDifference
In 32nds23/3224/321/32
Decimal inches0.718750.750.03125
Millimeters18.25619.050.794
Share of 3/4 inch95.83%100%4.17%

Every cell is arithmetic from the fractions and 1 in = 25.4 mm.

Why a 3/4 Inch Sheet Is 23/32 Inch

Guides give three causes: pressing compresses the veneers, sanding removes wood from the faces and wood shrinks as it dries. Mills tool for panels slightly under nominal, not over it.

Woodworking Advisor puts the sanding loss at roughly 1/64 inch per face. Inch Calculator says undersizing is common across sizes. Its chart shows every common panel 1/32 inch under nominal, as the table below confirms.

Nominal and actual plywood thickness in fractions, decimals and millimeters
NominalActualActual in decimalsActual in mmGap
1/4 in7/32 in0.218755.560.03125 in
1/2 in15/32 in0.4687511.910.03125 in
5/8 in19/32 in0.5937515.080.03125 in
3/4 in23/32 in0.7187518.260.03125 in

Source for the nominal and actual pairs: Inch Calculator, updated May 3, 2023. Decimals and millimeters are computed here. Inch Calculator rounds some millimeter values.

Plywood Thickness by Panel Type

Not every 3/4 inch panel is 23/32 inch. Sanded grades can run thinner, and Baltic birch is built to a metric size.

Actual thickness by plywood type, from Woodworking Advisor
Panel typeActual thickness
Sheathing or CDX, unsanded softwood23/32 in
Sanded A/B/C softwood45/64 to 23/32 in (0.703125 to 0.71875)
Hardwood plywoodAbout 23/32 in
Baltic birch18 mm (0.7087 in)
Panels over 1 in, such as 1-1/8 and 1-1/4 inGenerally true to nominal

Source: Woodworking Advisor, modified September 6, 2026. A retail listing for rated sheathing from Home Depot also names the thickness 23/32 inch. The 45/64 inch figure is one source's number. Check it with a caliper.

When 1/32 Inch Matters

It matters when parts must fit each other: grooves, stacked layers and joins at a floor edge. It rarely matters for roof sheathing.

  1. Grooves. A 3/4 inch bit cuts a 0.75 inch groove. A 23/32 inch panel in it leaves 0.03125 inches of slack.
  2. Two layers. Two 23/32 inch layers stack to 1.4375 inches. Two true 3/4 inch layers stack to 1.5 inches. The stack is 0.0625 inch short.
  3. Three layers. 2.15625 inches against 2.25 inches, which is 0.09375 inch short.
  4. Sanded sheets. If a sanded sheet measures 45/64 inch, it is 0.015625 inch thinner than 23/32 inch.

Measure the sheet with a caliper, near each corner and in the center, and cut the groove to the measured value. Do not size a groove from the label. For quantity work, such as how many sheets a floor needs, the plywood calculator works in sheets, not thickness. To convert the numbers here, use the feet and inches calculator.

Warning
Check structural use with a professional. This page compares sizes. Panel ratings, spans and fastening for floors, roofs and walls come from the panel stamp, the code and your engineer.

Frequently Asked Questions

Advertisement

For other size questions, see feet vs inches and the conversion calculators.

Sources and Review

The fraction, decimal and millimeter figures are arithmetic. The trade facts come from the pages below, read on November 22, 2026. APA's own thickness table was not on the pages read.

  • Inch Calculator, Actual Plywood Thickness and Size, inchcalculator.com/actual-plywood-thickness-size/, updated May 3, 2023.
  • Woodworking Advisor, How Thick Is 3/4 Inch Plywood?, woodworkingadvisor.com/23-32-vs-3-4-plywood, modified September 6, 2026.
  • Engineer Fix, What Is the Actual Size of 23/32 Plywood?, engineerfix.com, January 7, 2026.
  • APA, Plywood, apawood.org/engineered-wood-products/plywood-osb/plywood/.
  • The Home Depot, 23/32 in. x 4 ft. x 8 ft. Rated Sheathing Plywood listing, read November 22, 2026.

Published November 2026. Last updated November 2026. Next review May 2027. Reviewer sign-off is pending.

Rachel Torres, M.Ed., M.Ed. — CalcSummit expert reviewer

Reviews: conversion calculators · 22 calculators reviewed

Full profile →